 |
| Quantity: | |
|---|---|
Polyethersulfone (PES), Nylon, Polytetrafluoroethylene (PTFE), Polypropylene (PP), Mixed cellulose (MCE), Polyvinylidene fluoride (PVDF)
Pharmaceutical, Microelectronics, Laboratory
The STFA capsule filter is produced in 100,000 clean workshops, strictly implementing ISO13485 & IOS9001 quality system. It is widely used in small batch fluid filtration in laboratory.
Features and Benefits
Good sealing and pressure resistance, 50.5mm chuck, can be directly connected to stainless steel pipeline
Disposable design, convenient and practical
Absolute precision filter membrane
Application
Filtration of serums, peptides, and cell products
Filtration of diagnostic reagents
Filtration of immunoanalyzer liquid path
Filtration of feed liquid
Bacteria-reducing and bacteria-removing filtration of medical purified water
Materials of Construction
Filter Media: PES/PTFE/Nylon/PP/MCE/GF/PVDF
Cage & Support & End Caps: PP
Drainage: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Membrane area: 2.2ft²/5”, 4.9ft²/ 10”
Operating Conditions
Max. Temperature: 60℃
Maximum Operating Pressure:
3.5 bar@23℃; 3.0 bar@60℃ (Liquid)
3.0 bar@23℃; 2.5 bar@60℃（air）
Removal Ratings (μm)
0.1, 0.22, 0.45, 0.65, 0.8, 1.2, 3.0, 5.0
Typical Liquid Flow Rate
Ordering Information
Series | Material | Rating(μm） | Length（in） | Seal |
STFA | P=PP | 01=0.1 | 02=2.5 | S= Silicone |
M=MCE | 022=0.22 | 05=5 | E= EPDM | |
N=Nylon | 045=0.45 | 1=10 | ||
T=PTFE | 065=0.65 | |||
TL=Hydrophilic PTFE | 1=1 | |||
V=PVDF | 3=3 | |||
VL=Hydrophilic PVDF | 10=10 | |||
G=GF | 0202=0.22+0.22 | |||
0204=0.22+0.45 |
The STFA capsule filter is produced in 100,000 clean workshops, strictly implementing ISO13485 & IOS9001 quality system. It is widely used in small batch fluid filtration in laboratory.
Features and Benefits
Good sealing and pressure resistance, 50.5mm chuck, can be directly connected to stainless steel pipeline
Disposable design, convenient and practical
Absolute precision filter membrane
Application
Filtration of serums, peptides, and cell products
Filtration of diagnostic reagents
Filtration of immunoanalyzer liquid path
Filtration of feed liquid
Bacteria-reducing and bacteria-removing filtration of medical purified water
Materials of Construction
Filter Media: PES/PTFE/Nylon/PP/MCE/GF/PVDF
Cage & Support & End Caps: PP
Drainage: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Membrane area: 2.2ft²/5”, 4.9ft²/ 10”
Operating Conditions
Max. Temperature: 60℃
Maximum Operating Pressure:
3.5 bar@23℃; 3.0 bar@60℃ (Liquid)
3.0 bar@23℃; 2.5 bar@60℃（air）
Removal Ratings (μm)
0.1, 0.22, 0.45, 0.65, 0.8, 1.2, 3.0, 5.0
Typical Liquid Flow Rate
Ordering Information
Series | Material | Rating(μm） | Length（in） | Seal |
STFA | P=PP | 01=0.1 | 02=2.5 | S= Silicone |
M=MCE | 022=0.22 | 05=5 | E= EPDM | |
N=Nylon | 045=0.45 | 1=10 | ||
T=PTFE | 065=0.65 | |||
TL=Hydrophilic PTFE | 1=1 | |||
V=PVDF | 3=3 | |||
VL=Hydrophilic PVDF | 10=10 | |||
G=GF | 0202=0.22+0.22 | |||
0204=0.22+0.45 |
