 |
| Quantity: | |
|---|---|
Nylon
Pharmaceutical
The manufacture process of FPN series filter cartridge from membrame production, injection molding, assembly manufacturing, internal packaging is in the whole process of 100,000 clean workshop. Each filter is tested for integrity before leaving the factory to ensure that the filter is clean, complete and reliable retention. This is a very cost-effective product.
Features and Benefits
Self-produced materials, cost-effective
Broad chemical compatibility
Great heat resistance
Application
Sterile filtration for SVPs and LVPs
Precision filtration of purified water and injection water
Animal liquid preparation filtration
Filtration for biologicals
Filtration for hospital water
Materials of Construction
Membrane：Nylon
Cage & Support & End Caps：PP
Drainage：PP
O-rings/Gasket：Silicone/Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
pH range: 6-12
Filtration Area
≥0.62 m2 /10”
Dimensions
Outer Diameter：68mm
Length（in）：10, 20, 30, 40
Pore Size (μm)
0.1, 0.22, 0.45, 0.8, 1.0, 3.0, 5.0, 0.1+0.22, 0.22+0.22, 0.22+0.45
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23)
0.22μm≥2.8bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPN | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
08=0.8 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
1=1.2 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
3=3.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
5=5.0 | G=215/Flat | M=PTFE gasket (soft) | ||||
0102=0.1+0.22 | ||||||
0202=0.22+0.22 | ||||||
0245=0.22+0.45 |
The manufacture process of FPN series filter cartridge from membrame production, injection molding, assembly manufacturing, internal packaging is in the whole process of 100,000 clean workshop. Each filter is tested for integrity before leaving the factory to ensure that the filter is clean, complete and reliable retention. This is a very cost-effective product.
Features and Benefits
Self-produced materials, cost-effective
Broad chemical compatibility
Great heat resistance
Application
Sterile filtration for SVPs and LVPs
Precision filtration of purified water and injection water
Animal liquid preparation filtration
Filtration for biologicals
Filtration for hospital water
Materials of Construction
Membrane：Nylon
Cage & Support & End Caps：PP
Drainage：PP
O-rings/Gasket：Silicone/Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
pH range: 6-12
Filtration Area
≥0.62 m2 /10”
Dimensions
Outer Diameter：68mm
Length（in）：10, 20, 30, 40
Pore Size (μm)
0.1, 0.22, 0.45, 0.8, 1.0, 3.0, 5.0, 0.1+0.22, 0.22+0.22, 0.22+0.45
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23)
0.22μm≥2.8bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPN | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
08=0.8 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
1=1.2 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
3=3.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
5=5.0 | G=215/Flat | M=PTFE gasket (soft) | ||||
0102=0.1+0.22 | ||||||
0202=0.22+0.22 | ||||||
0245=0.22+0.45 |
