Availability: | |
---|---|
Quantity: | |
Polypropylene (PP)
Pharmaceutical
FPP series filter cartridge is made of microfiber PP filter material, long fiber spunbonded non-woven fabric and high purity PP skeleton. The filter cartridge achieves multi-level step by step filtration, and the Loongfiltech FPP filter cartridge has high throughput and long service life. The filter membrane of this series of filter cartridge has no fiber shedding and no impurity precipitation, which eliminates the pollution risk caused by the use of it.
Features and Benefits
Microfiber membrane with higher retention rate
No fiber shedding, low precipitation
Multi-gradient step by step filtration design
High dirt-holding capacity, long service life
Application
Pre-filtration of infusion and injection
Pure water system security filter element
Clarification filtration of biological products
Pre-filtration of apis
Solvent filtration
Materials of Construction
Membrane: PP
Cage & Support & End Caps: PP
Drainage: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP<60℃
PP with stainless steel lined end cap<85℃
PP with stainless steel lining<95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
pH range:1-14
Filtration Area
≥0.41 m2 /10”
Dimensions
Outer Diameter: 68mm
Length(in): 10, 20, 30, 40
Pore Size (μm)
0.1, 0.22, 0.45, 0.65, 1.0, 3.0, 5.0, 10, 20, 50
Biosafety
Endotoxin:<0.25EU/ml
Extractable: ≤50mg/10 in
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPP | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
065=0.65 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
1=1.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
3=3.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
5=5.0 | G=215/Flat | M=PTFE gasket (soft) | ||||
10=10.0 | ||||||
20=20.0 | ||||||
50=50.0 |
FPP series filter cartridge is made of microfiber PP filter material, long fiber spunbonded non-woven fabric and high purity PP skeleton. The filter cartridge achieves multi-level step by step filtration, and the Loongfiltech FPP filter cartridge has high throughput and long service life. The filter membrane of this series of filter cartridge has no fiber shedding and no impurity precipitation, which eliminates the pollution risk caused by the use of it.
Features and Benefits
Microfiber membrane with higher retention rate
No fiber shedding, low precipitation
Multi-gradient step by step filtration design
High dirt-holding capacity, long service life
Application
Pre-filtration of infusion and injection
Pure water system security filter element
Clarification filtration of biological products
Pre-filtration of apis
Solvent filtration
Materials of Construction
Membrane: PP
Cage & Support & End Caps: PP
Drainage: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP<60℃
PP with stainless steel lined end cap<85℃
PP with stainless steel lining<95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
pH range:1-14
Filtration Area
≥0.41 m2 /10”
Dimensions
Outer Diameter: 68mm
Length(in): 10, 20, 30, 40
Pore Size (μm)
0.1, 0.22, 0.45, 0.65, 1.0, 3.0, 5.0, 10, 20, 50
Biosafety
Endotoxin:<0.25EU/ml
Extractable: ≤50mg/10 in
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPP | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
065=0.65 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
1=1.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
3=3.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
5=5.0 | G=215/Flat | M=PTFE gasket (soft) | ||||
10=10.0 | ||||||
20=20.0 | ||||||
50=50.0 |