 |
| Quantity: | |
|---|---|
Mixed cellulose (MCE)
Pharmaceutical
This series of filters cartridge adopts hydrophilic MCE membrane, which has high throughput and low protein adsorption performance, and is widely used in the pre-filtration of vaccines, blood products and other biological products in biopharmaceuticals. Produced in a clean environment, 100% of the products are tested for integrity and washed with high purity water.
Features and Benefits
Hydrophilic mixed cellulose membrane
Very low protein adsorption
High flow rate, high flux
Economical pre-filter cartridge for biological products
Application
Prefiltration of biological products
Ultra pure water terminal filtration
Filtration of diagnostic reagents
Serum pre-filtration, sterile filtration
Materials of Construction
Membrane：MCE membrane
Cage & Support & End Caps：PP
Drainage：PP
O-rings/Gasket：Silicone/Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Steam sterilization 123℃@30min
Pore Size (μm)
0.1, 0.22, 0.45, 1.0, 3.0, 5.0
Filtration Area
≥0.55m2 /10”
Dimensions
Outer Diameter：68mm
Length（in）：10, 20, 30, 40
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23℃)
0.22μm≥1.0bar
0.45μm≥0.5bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPM | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
1=1.2 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
3=3.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
5=5.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
G=215/Flat | M=PTFE gasket (soft) |
This series of filters cartridge adopts hydrophilic MCE membrane, which has high throughput and low protein adsorption performance, and is widely used in the pre-filtration of vaccines, blood products and other biological products in biopharmaceuticals. Produced in a clean environment, 100% of the products are tested for integrity and washed with high purity water.
Features and Benefits
Hydrophilic mixed cellulose membrane
Very low protein adsorption
High flow rate, high flux
Economical pre-filter cartridge for biological products
Application
Prefiltration of biological products
Ultra pure water terminal filtration
Filtration of diagnostic reagents
Serum pre-filtration, sterile filtration
Materials of Construction
Membrane：MCE membrane
Cage & Support & End Caps：PP
Drainage：PP
O-rings/Gasket：Silicone/Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Steam sterilization 123℃@30min
Pore Size (μm)
0.1, 0.22, 0.45, 1.0, 3.0, 5.0
Filtration Area
≥0.55m2 /10”
Dimensions
Outer Diameter：68mm
Length（in）：10, 20, 30, 40
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23℃)
0.22μm≥1.0bar
0.45μm≥0.5bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPM | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | B= Interface lining steel | S= Silicone |
022=0.22 | B=222/Flat | 05=5" | B=PBT | C= Fully lining | E= EPDM | |
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
1=1.2 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
3=3.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
5=5.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
G=215/Flat | M=PTFE gasket (soft) |
