 |
| Quantity: | |
|---|---|
Polyethersulfone (PES)
Pharmaceutical
The filter cartridge is made of hydrophilic PES membrane and PP skeleton. The membrane material is made of asymmetric PES membrane with very low extractables. The filter cartridge has great heat resistance and can withstand multiple steam sterilization. Each cartridge is tested for integrity before leaving the factory. The filter cartridge also has excellent corrosion resistance, which can be tolerated in common acids, alkalis and chemical solvents. It can be widely used in life science fields such as biopharmaceutical & medical industries.
Features and Benefits
High purity material, low dissolution
high dirt-holding capacity and long service life
Good hydrophilicity
Easy to be wet
Great heat resistance
Application
Sterile filtration for SVP and LVP
Sterile filtration of freeze-dried powder needle
Sterile filtration of disinfectant
Ultrapure water filtration
Materials of Construction
Membrane: Hydrophilic PES
Cage & Support & End Caps: PP
Drainage：PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Steam sterilization 123℃@30min
pH range: 1-14
Filtration Area
≥0.6 m2 /10”
Removal Ratings (μm)
0.03, 0.1, 0.22, 0.45, 0.8, 1.2, 0.1+0.22, 0.22+0.22, 0.22+0.45
Dimensions
Outer Diameter: 68mm/70mm
Length（in）: 10, 20, 30, 40
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23℃)
0.1μm≥3.8bar
0.22μm≥3.4bar
0.45μm≥2.3bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPS | 003=0.03 | A=222/Fin | 02=2.5" | P=PP | S= Silicone | |
01=0.1 | B=222/Flat | 05=5" | B=PBT | E= EPDM | ||
022=0.22 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
045=0.45 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
08=0.8 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
1=1.2 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
0122=0.1+0.22 | G=215/Flat | M=PTFE gasket (soft) | ||||
0202=0.22+0.22 | ||||||
0245=0.22+0.45 |
The filter cartridge is made of hydrophilic PES membrane and PP skeleton. The membrane material is made of asymmetric PES membrane with very low extractables. The filter cartridge has great heat resistance and can withstand multiple steam sterilization. Each cartridge is tested for integrity before leaving the factory. The filter cartridge also has excellent corrosion resistance, which can be tolerated in common acids, alkalis and chemical solvents. It can be widely used in life science fields such as biopharmaceutical & medical industries.
Features and Benefits
High purity material, low dissolution
high dirt-holding capacity and long service life
Good hydrophilicity
Easy to be wet
Great heat resistance
Application
Sterile filtration for SVP and LVP
Sterile filtration of freeze-dried powder needle
Sterile filtration of disinfectant
Ultrapure water filtration
Materials of Construction
Membrane: Hydrophilic PES
Cage & Support & End Caps: PP
Drainage：PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Steam sterilization 123℃@30min
pH range: 1-14
Filtration Area
≥0.6 m2 /10”
Removal Ratings (μm)
0.03, 0.1, 0.22, 0.45, 0.8, 1.2, 0.1+0.22, 0.22+0.22, 0.22+0.45
Dimensions
Outer Diameter: 68mm/70mm
Length（in）: 10, 20, 30, 40
Biosafety
Endotoxin:＜0.25EU/ml
Extractable: ≤50mg/10 in
Integrity Test (BP, Water@23℃)
0.1μm≥3.8bar
0.22μm≥3.4bar
0.45μm≥2.3bar
Typical Liquid Flow Rate
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FPS | 003=0.03 | A=222/Fin | 02=2.5" | P=PP | S= Silicone | |
01=0.1 | B=222/Flat | 05=5" | B=PBT | E= EPDM | ||
022=0.22 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
045=0.45 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
08=0.8 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
1=1.2 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket (hard) | ||
0122=0.1+0.22 | G=215/Flat | M=PTFE gasket (soft) | ||||
0202=0.22+0.22 | ||||||
0245=0.22+0.45 |
