 |
| Quantity: | |
|---|---|
Polypropylene (PP)
Microelectronics
The FEP series filter cartridge is made of microfiber PP filter material, long fiber spunbonded non-woven fabric and high purity PP skeleton. They are characterized by multiple layers of progressively pleated polypropylene fine fiber. The filter material in the filter cartridge has undergone a special post-treatment process, no fiber falling off, no impurities precipitation, eliminating the pollution risk caused by the use of the filter cartridge to the material.
Features and Benefits
Microfiber material with higher retention rate
No fiber shedding, low precipitation
Multi-gradient step by step filtration design
Superior dirt-holding capacity, long service life
Application
Final filtration for reagent-grade aggressive solutions
Filtration for monomers of optical resin
Filtration for silicone oil
Materials of Construction
Membrane: multiple layers of PP
Cage & Support & End Caps: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Filtration Area
≥0.41 m2 /10”
Typical Liquid Flow Rate
Dimensions
Outer Diameter: 68mm
Length（in）: 10, 20, 30, 40
Removal Ratings (μm)
0.1，0.22，0.45，1.0，3.0，5.0，10，20
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FEP | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | S= Silicone | |
022=0.22 | B=222/Flat | 05=5" | B=PBT | E= EPDM | ||
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
1=1.0 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
3=3.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
5=5.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket(hard） | ||
10=10.0 | G=215/Flat | M=PTFE gasket(soft) | ||||
20=20.0 |
The FEP series filter cartridge is made of microfiber PP filter material, long fiber spunbonded non-woven fabric and high purity PP skeleton. They are characterized by multiple layers of progressively pleated polypropylene fine fiber. The filter material in the filter cartridge has undergone a special post-treatment process, no fiber falling off, no impurities precipitation, eliminating the pollution risk caused by the use of the filter cartridge to the material.
Features and Benefits
Microfiber material with higher retention rate
No fiber shedding, low precipitation
Multi-gradient step by step filtration design
Superior dirt-holding capacity, long service life
Application
Final filtration for reagent-grade aggressive solutions
Filtration for monomers of optical resin
Filtration for silicone oil
Materials of Construction
Membrane: multiple layers of PP
Cage & Support & End Caps: PP
O-rings/Gasket: Silicone /Viton /EPDM/TEV
Performance Characteristics
PP＜60℃
PP with stainless steel lined end cap＜85℃
PP with stainless steel lining＜95℃
Positive/Reverse pressure resistance 4bar/2bar (23℃)
Filtration Area
≥0.41 m2 /10”
Typical Liquid Flow Rate
Dimensions
Outer Diameter: 68mm
Length（in）: 10, 20, 30, 40
Removal Ratings (μm)
0.1，0.22，0.45，1.0，3.0，5.0，10，20
Ordering Information
Series | Rating(μm) | End Cap | Length(in) | Support | Port | Seal |
FEP | 01=0.1 | A=222/Fin | 02=2.5" | P=PP | S= Silicone | |
022=0.22 | B=222/Flat | 05=5" | B=PBT | E= EPDM | ||
045=0.45 | C=226/Fin | 1=10" | V=PVDF | D= Skeleton lining | V= Viton | |
1=1.0 | D=226/Flat | 2=20" | F=PFA | T= TEV | ||
3=3.0 | E=DOE/Flat | 3=30" | M=PE | N=Butyronitrile | ||
5=5.0 | F=215/Fin | 4=40" | G=GF | F=PTFE gasket(hard） | ||
10=10.0 | G=215/Flat | M=PTFE gasket(soft) | ||||
20=20.0 |
